M4A3E2 (76) W

This page is about the American heavy tank M4A3E2 (76) W. For other M4 Shermans, see M4 Sherman (Family). For other uses, see M4 (Disambiguation).

M4A3E2 (76) W

T1E1 (90)

T26E5

M4A3E2 (76) W

T1E1 (90)

T26E5

USA

IV Rank

Battle rating:

AB	RB	SB
6.3	6.3	6.3

Class:

Heavy tank

Research:46 000

Purchase:155 000

Show in game

Description

The M4A3E2 (76) W Sherman - Assault Tank, also known as the "Jumbo", is a special up-gunned and armoured modification of the M4A3, which is the fourth variant of the early-generation Medium Tank M4 (Sherman) family. Approximately 100 M4A3E2s were up-gunned to 76 mm M1 tank guns in February 1945, using supplies salvaged from knocked-out late-generation M4 Shermans and standard supply stocks. Since the M4A3E2 gun mount was originally designed for the 76 mm M1 tank gun, this upgrade was a relatively simple field upgrade. The reorganization of the main tank gun ammunition stowage was the most difficult part of the upgrade. This necessitated the removal of the turret as well as the installation of 76 mm ammunition racks in place of the shorter 75 mm ammunition racks. These replacement racks were then held in place by a series of custom-made welded bracing. According to records, such a modification required around 75 hours per tank. It should be emphasized that the term 'Jumbo' does not exist in any military material and is probably certainly a post-war nickname, possibly developed by a model organization.

Introduced in Update 1.45 "Steel Generals(introduced 16 December 2014)", the M4A3E2 (76) W improves on the previous M4A3E2, which was based on the original M4A3 Sherman variant. The M4A3E2 (76) W finally gives players the much-needed improvement in armour penetration, allowing it to deal with adversaries from the front considerably more easily. However, due to the increased battle rating of the M4A3E2 (76) W and the abundance of even stronger opponents, the tank's frontal armour protection is no longer as effective as it was with the preceding M4A3E2. Due to considerable advancements in firepower, enemies at this rank may frequently penetrate the M4A2E2 (76) W from the front with ease. Nonetheless, this is a significant and welcome firepower improvement that is critical for the M4A3E2 (76) W. Players must be more cautious throughout battle as adversaries' weaponry becomes increasingly powerful.

General info

Survivability and armour

Armourfront / side / back

Hull101 / 76 / 38

Turret177 / 152 / 152

Crew5 people

Visibility122 %

Armour type:

• Rolled homogeneous armour (Front, Side, Rear, Roof)
• Cast homogeneous armour (Turret, Transmission area)

Armour	Front (Slope angle)	Sides	Rear	Roof
Hull	63.5 + 38.1 mm (47°)	76.2 mm	38.1 mm	19.5 mm
Turret	177.8 mm	152.4 mm	152.4 mm	25.4 mm

Mobility

Speedforward / back

AB38 / 5 km/h

RB and SB36 / 5 km/h

Number of gears5 forward

1 back

Weight37.8 t

Engine power

AB954 hp

RB and SB500 hp

Power-to-weight ratio

AB25.2 hp/t

RB and SB13.2 hp/t

Game Mode	Max Speed (km/h)		Weight (tons)	Engine power (horsepower)		Power-to-weight ratio (hp/ton)
	Forward	Reverse		Stock	Upgraded	Stock	Upgraded
Arcade	38	5	37.8	646	954	17.09	25.24
Realistic	36	5		442	500	11.69	13.23

Modifications and economy

Repair costBasic → Reference

AB3 028 → 3 745

RB3 258 → 4 030

SB4 397 → 5 439

Total cost of modifications40 300

77 800

Talisman cost1 400

Crew training45 000

Experts155 000

Aces630

Research Aces440 000

Reward for battleAB / RB / SB

110 / 160 / 180 %

160 / 160 / 160 %

Modifications

Mobility	Protection	Firepower
Tracks Research: 2 700 Cost: 5 200 165 Suspension Research: 1 800 Cost: 3 500 110 Brake System Research: 1 800 Cost: 3 500 110 Filters Research: 2 500 Cost: 4 800 155 Transmission Research: 4 400 Cost: 8 500 270 Engine Research: 4 400 Cost: 8 500 270	Improved Parts Research: 2 700 Cost: 5 200 165 Improved FPE Research: 1 800 Cost: 3 500 110 Crew Replenishment Research: 2 500 Cost: 4 800 155	Horizontal Drive Research: 2 700 Cost: 5 200 165 Adjustment of Fire Research: 1 800 Cost: 3 500 110 76mm_usa_APCBC_ammo_pack Research: 1 800 Cost: 3 500 110 Elevation Mechanism Research: 2 500 Cost: 4 800 155 76mm_usa_M93_APCR_ammo_pack Research: 2 500 Cost: 4 800 155 76mm_us_M88_Smoke_ammo_pack Research: 4 400 Cost: 8 500 270

To start out, you will want to get Tracks, Parts, then M62 Shell, and work your way from there, as those are the core components of the M4A3E2 (76) W Sherman Jumbo. With the better ammunition, you will be able to penetrate more and be far more dangerous on the field. And with Tracks & Parts, you won't need to worry about the lights/mediums that keep popping out your tracks to get to your side or backside. After getting these three things, it's best to work on manoeuvrability and M93 Shot as a first priority.

Armaments

Main armament

76 mm M1 cannon

Vertical stabilizer

Reduces the swing of the gun in one plane while moving

Ammunition71 rounds

Reloadbasic crew → aces

7.6 → 5.9 s

Vertical guidance-10° / 25°

76 mm M1					Turret rotation speed (°/s)					Reloading rate (seconds)
Mode	Capacity	Vertical	Horizontal	Stabilizer	Stock	Upgraded	Full	Expert	Aced	Stock	Full	Expert	Aced
Arcade	71	-10°/+25°	±180°	Vertical	19.4	26.9	32.6	36.1	38.4	7.67	6.79	6.25	5.90
Realistic					14.3	16.8	20.4	22.6	24.0

Ammunition

• M79 shot - The M79 AP shot is the stock shell, it has 15 mm penetration less than the M62 at point blank while also lacking any explosive filler. Inferior in almost every way to the M62, it should be replaced by it as soon as possible.

• M42A1 shell - This is the HE shell of the M4A3E2 (76) W. It's best to use this when fighting AA trucks or other lightly-armoured tanks. Carry only 1 to 5 of these shells as you won't really need them, but they're useful for when a pesky AA truck comes around the corner and you're firing APCR at it.

• M62 shell - It is recommended to research this shell as soon as possible. With a 149 mm top penetration, the M62 APCBC shot usually won't be able to destroy heavy opponents or tank destroyers it will see at its BR from the front, however, the armour makes up for it to have more time looking for a good shot. Although only a minor upgrade from the stock M79, it is quite handy, and can deal with many of the opponents at its BR if you know where to aim. For one thing, this shell can destroy most cannon barrels with a direct hit.

• M93 shot - This APCR round is the last ammunition upgrade of the M4A3E2 (76) W. With a penetration upgrade of 40 mm over the M62 shell, this will be the best shell for the M4A3E2 (76) W Sherman Jumbo. With this shell, you'll be able to penetrate even the most armoured of opponents, except perhaps the occasional Tiger II or IS-2.

Penetration statistics
Ammunition	Type of warhead	Penetration @ 0° Angle of Attack (mm)
		10 m	100 m	500 m	1,000 m	1,500 m	2,000 m
M79 shot	AP	134	132	121	109	99	89
M42A1 shell	HE	16	16	14	13	11	10
M62 shell	APCBC	149	146	133	119	106	94
M93 shot	APCR	190	186	167	146	128	112

Shell details
Ammunition	Type of warhead	Velocity (m/s)	Projectile mass (kg)	Fuse delay (m)	Fuse sensitivity (mm)	Explosive mass (TNT equivalent) (g)	Ricochet
							0%	50%	100%
M79 shot	AP	792	6.8	-	-	-	47°	60°	65°
M42A1 shell	HE	823	5.84	0.2	0.1	390	79°	80°	81°
M62 shell	APCBC	792	7	1.2	14	63.7	48°	63°	71°
M93 shot	APCR	1,036	4.22	-	-	-	66°	70°	72°

Smoke shell characteristics
Ammunition	Velocity (m/s)	Projectile mass (kg)	Screen radius (m)	Screen deploy time (s)	Screen hold time (s)	Explosive mass (TNT equivalent) (g)
M88	274	3.44	13	5	20	50

Ammo racks

Ammo racks of the M4A1 (75) W (China) (identical)

Full ammo	1st rack empty	2nd rack empty	3rd rack empty	Visual discrepancy
71	66 (+5)	31 (+40)	1 (+70)	No

Note:

• Shells are modeled individually and disappear from the rack after having been shot or loaded.

Machine guns

12.7 mm M2HB machine gun

Ammunition600 rounds

Belt capacity200 rounds

Reloadbasic crew → aces

10.4 → 8.0 s

Fire rate575 shots/min

Vertical guidance-10° / 30°

Horizontal guidance-60° / 60°

7.62 mm M1919A4 machine gun (coaxial)

Ammunition3 000 rounds

Belt capacity250 rounds

Reloadbasic crew → aces

10.4 → 8.0 s

Fire rate500 shots/min

12.7 mm M2HB
Mount	Capacity (Belt)	Fire rate	Vertical	Horizontal
Pintle	600 (200)	577	-10°/+30°	±60°

7.62 mm M1919A4
Mount	Capacity (Belt)	Fire rate	Vertical	Horizontal
Coaxial	3,000 (250)	500	N/A	N/A

Usage in battles

Although based on a medium tank, the M4A3E2 (76) W the weight of its additional armor means that it is slower than most medium tanks at its rank.

The M4A3E2 (76) W regularly faces the Tiger IIs and Jagdpanthers. The best way to deal with these are to flank and disable them quickly. If this is not possible, the best tactic is often to disable their modules while retreating to wait for your allies to assist. Focus on taking out their guns and tracks while moving to cover. Avoid engaging them frontally if at all possible, especially at long ranges.

Most Soviet tanks at this rank share an easy to identify weak spot: the turret ring. A single well-placed shot to this area, where the turret meets the hull, will usually kill their gunner and prevent them from returning fire. In addition, destorying the turret ring will prevent them from moving their gun horizontally until repaired.

Like all M4 variants, the sides of the M4A3E2 (76) W are large, vertical, and poorly armored. The frontal armor is your best defense, and should be used to maximum advantage. Maintaining awareness of the number and position of the enemies that you face is key, as they will attempt to flank you to position themselves for a side shot.

To ensure that you can get a good shot, find out what enemy tanks you'll see in the Jumbo then check where their ammo is and how much armour is protecting that area. If you know you can penetrate that, go for the ammo/gunner/gun, as the M93 shot does not fragment or have a HE filler, it simply pierces the tank and goes straight through.

Environments

In urban environments, you're going to want to move up with the rest of the group, however, don't move up as the lead tank because you will surely find a nasty surprise at the end of the road. When facing Tiger II's, they will be able to penetrate anywhere they want in your frontal armour, even your thickest point (turret) if their ammo is upgraded enough. It's best to shoot the flat part of the turret, or get to their sides and penetrate them. However, if you can't do either of those, track them and hope that something bigger on your team will be able to take it out. The M93 can penetrate the front of the Tiger II (P), but not the H model.

In open terrain, you can usually brawl from long-range with certain tanks, such as the Tiger I, and mediums of Russia. However, if you see a Tiger II or other formidable opponent, it's best to stay far and show your front, angling the best. You can also use the hills to your advantage as most tanks do, and hide behind them before quickly moving out of cover, taking pot-shots at the enemy tank then heading back into cover.

Arcade battles

In Arcade Battles you will usually see some pretty nasty tanks, however, because of your turret and hull armour, you will be able to usually survive. Use the player-name system to your advantage and shoot enemy tanks when they're not looking. However, because it's arcade and you're much more likely to be hit, it's best to angle your armour at a slightly less 35-degree angle. In AB, you will most likely have an advantage if you make the first shot, you're fast, and you never show your side.

Realistic/Simulator battles

This is where you should aim with the M62 shell to penetrate a Tiger from the front.

In realistic battles and simulator battles, your opponents will be much more battle hardened and know where to shoot the Jumbo. When facing enemy tanks, don't always suspect that you can just show your frontal armour and turret and expect to not get penetrated. As said before, be safe and be quick, and angle your armour when you can because that saves lives. You never want to go solo and move up on your own, as you will most definitely meet a tank destroyer or quite possibly a heavy tank. When meeting an IS-2, a turret hit or shot between the hull and turret will usually cripple it, but when facing a Tiger II you'll have to be a bit more careful, as the tank is bigger and stronger than you. Although your M93 shot usually has the penetration power, it cannot penetrate the Tiger II's hull and your best luck will be shooting the flat armour of the turret front.

Tiger I E: This is a tough opponent to face, but, it can be killed quite easily if you know what to do. With the M62 round, you should aim at the area shown in the picture. It will penetrate the Tiger unless it is very sharply angled, but that could often mean that you can get a side shot. Do not aim for the drivers viewport or the machine gun, just aim for the flat armour on this section of the tank.

This is the most most surefire way to disable a Panther quickly.

Panther: This is another very common and tough opponent to face. Do not shoot for the hull front, it will not be able to penetrate. You can try to shoot the turret front, but there is a chance you will bounce. The most surefire way to disable a Panther is to shoot the commander's cupola, highlighted on the left. This will often kill the commander and gunner, and about half the time it will also kill the loader.

IS-2: This is one common opponent from the Soviet/Chinese tree. Its 122 mm gun can easily penetrate the Jumbo, regardless of angle and distance. To destroy it, shoot at it when it's reloading or is unaware of your presence. For the 1943 model, aim at the cupola or the curved part of its hull armour that blends into the side. It has only 4 crew so killing all the turret crew (3, which is easy) will destroy it. For the 1944 model, only aim at the turret or the cupola as its hull is very strong.

Against the M4A3E2

Light tank/SPAA: the Jumbo will be a very tough opponent for these light vehicles simply due to its thick armour. Use your good mobility and flank it whenever you can. Do not shoot at the turret at all times since it is 152 mm thick all-round, which is immune to almost all rounds from light vehicles. As you are at its side, target the lower part of the hull side where it is only 38 mm thick and can be penetrated by even low BR tanks like M5A1. Penetrating shells through there will knock out all of its crew. Breaking its barrel or tracks can also be an option, but beware of its turning turret and roof mounted heavy MG. It might take several hits thus longer time to disable these modules, so retreat if there is danger.

Medium tank: medium tank commanders will have a better time dealing with an M4A3E2 as they are now better armed while also having adequate mobility to flank around. When the Jumbo is angling it is generally still impossible to penetrate. However if its angle is a bit too much and exposes more of its side, shells with good performance against sloped armour (e.g. BR-365A) will easily go through the lower part of the hull side, right above the front sprocket wheel. If the engagement distance is very close and the Jumbo does not have bushes, you can probably see its famous weak spot: the MG port. Aim carefully at it, as it has a chance to bounce or absorb a shell. A penetration through there will usually destroy the target. At this close range, certain tanks like T-34-85 and Panther A may not need to aim at the MG port, as they can punch straight through the upper front plate with ballistic capped shells or superior penetration.

Heavy tank/tank destroyer: since these heavier vehicles (e.g. IS-2) generally come with extreme penetrations, there is not much to say. Target the M4A3E2's upper frontal plate if it is not angling. If it is, aim at the gun mantlet or lower side armour. Do not hit the weld line that joins the curved transmission housing with the flat upper front plate, it is very likely to absorb the shell.

Pros and cons

Pros:

• Better 76 mm armour-piercing power compared to previous version, especially with APCR when available
• One of the fastest reloading armament for a heavy tank of the rank
• Good gun depression of -10 degrees, can help fighting at hull-down positions
• Equipped with a stabiliser to allow fire-on-the-move at low speed
• Jumbo armour layout gives enhanced frontal protection for the hull and turret, especially so when angled
• Weak spots on front hull are small and are hard to hit at longer ranges
• Centralised "wet" ammunition stowage in the centre, reducing chance of a penetrating shot igniting the ammunition
• Good forward acceleration to get on the move quickly

Cons:

• Constantly faces enemy tanks with guns able to easily penetrate the front armour
• Angling benefit to frontal hull armour is mitigated by extremely thin lower side armour, which can be easily penetrated by enemy guns
• Due to the layered armour at the front and the armour over-matching mechanic, the upper glacis armour can be dubious in that it does not reliably ricochet shells, even from smaller calibre guns like the 75 mm SA50
• Aiming at dangerous enemy tanks can allow them to attack the relatively flat gun mantlet or the weaker area above mantlet, penetrating and knocking out the gun, the turret crew, or both
• 76 mm gun may find itself lacking against enemy frontal armour, requiring some good shot placement and/or tactical manoeuvres
• Roof armour is thin enough that some aerial attack at a perpendicular angle can penetrate
• Tall profile makes it a bigger target
• Bad off-road manoeuvrability
• Quite low top speed of 35 km/h, with a likewise bad reverse speed of -4 km/h

History

Development

Long before D-Day, American war planners knew that it would a long and decisive battle against the German defensive and that the need for an assault tank to push the lines and capture the beach was needed. The Americans knew they would need a tank that was up-armoured and up-gunned, something beyond the standard M4 Sherman. The hope was the have the M26 Pershing finished by 1944, however, because of difficulties, it was delayed to 1945.

US Ordnance then took their abundant M4 Shermans in stock and fixed them up for the new role they've been assigned in. Although keeping the same engine, the armour was upped from around 76.2 mm initial thickness to 102 mm and angled at 47 degrees from vertical. This angle would influence later Sherman design such as the M4A3 by changing the original 56 degrees angled glacis with protruding crew hatches to 47 degrees angled glacis without any protrusion from the crew hatches. This modified M4 Sherman's armour when angled would then be 150 mm line-of-sight (LOS) thick and 180 mm effective. The side armour is also increased to 76.2 mm thick and the turret is redesigned to provide more protection. These modified Shermans were designated the M4A3E2 by the Ordnance Department, whereas the nickname "Jumbo" was likely a post-war invention. At the end of the modifications, the Sherman "Jumbo" now weighed about 42 tons and moves a lower speed of 22 mph. A drawback to the increased weight of the Sherman is that the Vertical Volute Suspension System (VVSS) from the Sherman was unable to take the weight easily, so extra care was taken by the crew members to not break the suspension.

In March of 1944, the US Army ordered for 254 of these vehicles to be delivered for use for European Operations. Intended for the assault on the Normandy Beachhead, it was deployed in Normandy after D-Day to assist the infantry push through German defences. The M4A3E2 originally came with the 75 mm guns to support infantry with its better HE shells compared to the planned 76 mm instalment, but the 76 mm was installed later in the campaign and called the M4A3E2 (76) W Jumbo.

Combat usage

The M4A3E2 was well-liked by the crew and commanders due to its protection value. Despite the weight difference and strain on the suspension, it performed reliably and could absorb damage that would otherwise destroy regular Shermans. Later in the war, when the quantity of the M4 Sherman "Jumbos" were unable to meet the demand, George S. Patton ordered for existing M4 Shermans to weld on armour plates scavenged from knocked out tanks to a makeshift "Expedient Jumbos". This caused the newer Shermans such as the M4A3 (76) W HVSS could have the same protection by welding metal onto the hull. One of the Jumbo's notable participation in the war was in Patton's Third Army where it spearheaded the assault to Bastogne to relieve the pinned down 101st Paratroopers.

When the war in the European Theater ended, the M4A3E2s were then placed stateside for the preparation for the invasion of the Japanese Home Islands. However, this was never to be fulfilled as Japan then surrendered to the United States in September 1945. The M4A3E2 Shermans proved to be a very effective stop-gap solution until heavier armoured tanks such as the Pershing could come into play. In 1948, about 96 Sherman Jumbos still remained in US inventory.

Archive of the in-game description

Preparations for the invasion of Europe saw a heavily armoured assault tank designated M4A3E2 (76)W designed using the M4A3 base. In March 1944 the Armed Forces Committee approved a program refitting 254 tanks, some of which were equipped with 76 mm cannons. Their armour was strengthened by stacking 38 mm armour plates welded together on the front and sides of the hull. As a result, the frontal armour reached a thickness of 102 mm to go along with the 76 mm on the sides. The transmission was protected with a 140 mm cast cover, while the rest of the hull was not modified. The new T23 cast turret had walls 152 mm thick and was special in that it did not have a hatch from which to fire a personal weapon. The 178 mm mantlet was mounted with a 76 mm M1A1C cannon, while ammunition was stored in wet stowage. The thicker armour pushed the tank's weight to 38 tons, simultaneously lowering its top speed to 35 km/h. The exact number of M4A3E2 tanks refitted with 76 mm M1A1C cannons was never ascertained. The tanks were very popular as column leads, given the fact that German antitank guns could not penetrate their frontal armour.

Media

Skins

• Skins and camouflages for the M4A3E2 (76) W from live.warthunder.com.

Videos

The Tiger 1's Worst Nightmare - M4A3E2 Jumbo (76) W - Virus

See also

Other M4A3E2 vehicles in the game

• M4A3E2
• Cobra King
• M4A3E2 (France)

External links

• [Tanks Encyclopedia] Assault Tank M4A3E2 Jumbo

U.S. Army Ordnance Department/Corps*
Light tanks	T18E2 · M24 (Designed in collaboration with Cadillac)
M3 Stuart	M3 · M3A1 Stuart · M3A1 (USMC)
M5 Stuart	M5A1
Medium tanks	M3 Lee
M4 Sherman	M4 · M4A1 · M4A2 · M4A3 (105) · Calliope
	M4A1 (76) W · M4A2 (76) W · M4A3 (76) W
M26 Pershing	T20 · T25 · M26 · M26E1 · M26 T99
Patton Series	M46 · M46 "Tiger" · M47
Prototypes	T54E1 · T95E1
Heavy tanks	M103
M4 Jumbo	M4A3E2 · Cobra King · M4A3E2 (76) W
M6 Heavy	M6A1 · M6A2E1 · T1E1
M26 Pershing	T26E1-1 · T26E5
Prototypes	T14
T29	T29 · T30 · T34
T-32	T32 · T32E1
Tank destroyers	M3 GMC · M10 GMC · M56
M8 GMC	M8 HMC · M8A1 GMC
M36 GMC	M36 GMC · M36B2
Prototypes	T28 · T95
SPAAGs
Production	M19 MGMC · M42
Export/Captured	␗M8 HMC · SU-57
Stuart	Stuart I · Stuart III · ␗M3A3 Stuart · ␗M3A3 (1st PTG) · ▄M3A3 · ▄M3A3 Stuart · ▃Stuart VI (5th CAD) · ␗M5A1
Lee/Grant	▂M3 Medium · ▃Grant I · Grant I
M4 Sherman	Sherman II · ▄M4A1 · ␗M4A1 (75) W · ▀M4 748 (a) · ▂M4A2 · ▄M4A3 (105) · ▅M4A3 (76) W · ▄M4A3E2
	␗M4A4 · ␗M4A4 (1st PTG) · ▄Sherman V · ▄M4A4 · ▄Sherman I Composito
M26 Pershing	M26 "D.C.Ariete" · M26A1
M47 Patton	mKPz M47 G · ▅M47
M10 GMC	␗M10 GMC · ▄M10 GMC
M36 GMC	␗M36 GMC · M36B1 · ▅M36 · ▄M36B2
M19 MGMC	▅M19A1
M42 MGMC	▅M42 · ␗M42
	*The Ordnance Department was renamed to the Ordnance Corps after the Army Reorganization Act of 1950.

USA heavy tanks
M4 Jumbo	M4A3E2 · Cobra King · M4A3E2 (76) W
M6	M6A1 · T1E1 · T1E1 (90) · M6A2E1
T26	T26E1-1 · T26E5
T29/30/34	T29 · T30 · T34
T32	T32 · T32E1
M103	M103
Others	T14