Leopard 2A4

This page is about the German medium tank Leopard 2A4. For other versions, see Leopard 2 (Family).

Leopard 2A4

Leopard 1A5

Leopard 2A5

}

Leopard 2A4

Leopard 1A5

Leopard 2A5

Germany

VII Rank

Battle rating:

AB	RB	SB
10.7	10.7	10.7

Class:

Medium tank

Research:300 000

Purchase:830 000

Show in game

Description

The Leopard 2A4 is a rank VII German medium tank with a battle rating of 10.7 (AB/RB/SB). It was introduced in Update 1.79 "Project X".

General info

Survivability and armour

Composite armour

Balanced protection against all types of ammunition

Smoke grenades

Creation of a smoke screen in front of the vehicle

Self-entrenching equipment

Creation of ramparts and trenches in soft ground

Armourfront / side / back

Hull80 / 65 / 25

Turret80 / 80 / 25

Crew4 people

Visibility95 %

Leopard 2A4 Protection Density Visualisation

The Leopard 2A4's kinetic protection is reasonable, with the turret cheeks near-invulnerable to all but the most powerful rounds (e.g. CL3143) and the upper front plate capable of protecting against less powerful rounds (e.g. M735) - however besides these sections the remainder of the vehicle is largely vulnerable to high-powered kinetic rounds; of note are the weak lower front plate and the gun mantlet, both of which are reasonably visible targets, as well as the gunner's optics.

The vehicle sports significantly better all-round chemical protection, with an upper hull and turret essentially immune to all but the most powerful ATGMs frontally, with upwards of 800mm worth of equivalent protection in places. Despite this, it's advisable to be wary of incoming ATGMs as a well-placed round may sneak past the heavily protected areas - and some missiles such as those of the ADATS will slice straight through even the turret cheeks.

As with most other MBTs, the 2A4 is particularly vulnerable from the sides and back.

The Leopard 2A4 is reasonably survivable, with some degree of crew spacing. However, from certain angles, the crew are placed in a straight line and successful penetration may impact three of the four crew members, resulting in a crew knock-out. In addition, well-placed side shots may impact all three turret crew members.

Ammunition is stored in the primary ammunition storage in the rear of the turret, or in the secondary storage next to the driver. The primary rack provides crew protection through the use of blow-out panels, however only has space for 15 rounds. When more than 16 rounds are taken to battle, ammunition will be stored in the significantly more vulnerable hull rack.

The Leopard 2A4's protection proves acceptable for long-range combat, although it's ill-advised to remain in one location for any extended period of time to avoid opposing vehicles being able to hone their shots onto your weak spots. The 2A4's protection should not be relied upon in urban or other close-range environments.

Armour type:

• Rolled homogeneous armour (hull sides, rear, and roof, turret sides, rear, and roof)
• High hardness rolled armour (hull front, turret front, gun mantlet)
• Cast homogeneous armour (gun mantlet frame)
• Composite screen (front side skirts)
• Structural stell (rear side skirts)

Armour	Front (Slope angle)	Sides	Rear	Roof
Hull	35 mm (53-82°) Upper glacis 40 mm (51°) Lower glacis 30 mm (82°) Driver's hatch	10 mm (5°) Upper hull 35 mm Lower forward hull 20 mm Lower rear hull 5 mm Side Skirts 100 mm Composite screening	20 mm (11°) Upper plate 20 mm (17°) Lower plate 20 mm (50°) Lower glacis	35 mm (8°) Front glacis 20 mm (0-8°) Hull sides and engine deck 5 mm Engine vents
Turret	35 mm (32-44°) Cheeks incl. Gunner optics 120+16 mm Mantlet	35 mm Forward 15 mm Rear	10+25 mm (10°) Basket 20 mm (70°) Turret underside	40 mm (82-85°) Forward centre 14 mm (72-77°) Forward sides 20 mm Rear incl. cupolas

Composite armour	Front	Sides
Hull	Upper + Lower glacis 90 - 350 mm Kinetic 243 - 600 mm Chemical
Turret	Turret cheeks 420 - 800 mm Kinetic 535 - 820 mm Chemical Gun mantlet 100 - 270 mm Kinetic 300 - 480 mm Chemical	Side armour 194 - 260 mm Kinetic 280 - 400 mm Chemical

Notes:

• Suspension wheels, tracks, and torsion bars are 20 mm thick.

Mobility

Speedforward / back

AB76 / 35 km/h

RB and SB69 / 31 km/h

Number of gears8 forward

4 back

Weight55.2 t

Engine power

AB2 862 hp

RB and SB1 500 hp

Power-to-weight ratio

AB51.8 hp/t

RB and SB27.2 hp/t

Game Mode	Max Speed (km/h)		Weight (tons)	Engine power (horsepower)		Power-to-weight ratio (hp/ton)
	Forward	Reverse		Stock	Upgraded	Stock	Upgraded
Arcade	76	35	55.2	2,032	2,862	36.81	51.85
Realistic	69	31		1,327	1,500	24.04	27.17

The Leopard 2A4 is powered by an MTU (MOTOREN-UND TURBINEN-UNION FRIEDRICHSHAFEN GMBH) MB 873 Ka-501 engine which produces a whopping 1,500 hp (1,100 KW), resulting in a power-to-weight ratio of slightly over 27 hp per tonne, compared to the ratio of the early Abrams and identical to the T-80U. As such, the Leopard 2A4 is quite mobile despite weighing over 55 tonnes, comfortably able to reach 72 km/h on-road and well capable of keeping up with its competitors. This allows for an active, aggressive playstyle, using the Leopard's high speed and good acceleration characteristics to get into an early flanking position or take early cap points - though it is important to keep in mind that opposition forces might attempt the same.

The Leopard 2A4 has a maximum reverse speed of 31 km/h which it reaches easily, allowing for a quick retreat in sub-optimal situations.

Modifications and economy

Repair costBasic → Reference

AB4 350 → 6 785

RB4 212 → 6 570

SB4 927 → 7 686

Total cost of modifications244 500

405 000

Talisman cost2 900

Crew training240 000

Experts830 000

Aces2 100

Research Aces1 140 000

Reward for battleAB / RB / SB

150 / 200 / 250 %

238 / 238 / 238 %

Modifications

Mobility	Protection	Firepower
Tracks Research: 13 000 Cost: 20 000 350 Suspension Research: 12 000 Cost: 19 000 330 Brake System Research: 12 000 Cost: 19 000 330 Filters Research: 13 000 Cost: 20 000 350 Transmission Research: 17 000 Cost: 26 000 460 Engine Research: 17 000 Cost: 26 000 460	Improved Parts Research: 3 900 Cost: 20 000 350 Improved FPE Research: 3 600 Cost: 19 000 330 Crew Replenishment Research: 13 000 Cost: 20 000 350	Horizontal Drive Research: 13 000 Cost: 20 000 350 120mm_NATO_APDS_FS_ammo_pack Research: 13 000 Cost: 20 000 350 Adjustment of Fire Research: 12 000 Cost: 19 000 330 Dozer Blade Research: 12 000 Cost: 19 000 330 Elevation Mechanism Research: 13 000 Cost: 20 000 350 Smoke grenade Research: 13 000 Cost: 20 000 350 NVD Research: 13 000 Cost: 20 000 350 Artillery Support Research: 17 000 Cost: 26 000 460 120mm_DM_APDS_FS_ammo_pack Research: 17 000 Cost: 26 000 460 Laser rangefinder Research: 17 000 Cost: 26 000 460

The first modifications to research should be Parts, FPE, and the DM13 round. After that, aim for the NVD, DM23, Laser rangefinder, or mobility upgrades, depending on the desired playstyle.

Armaments

Laser rangefinder

Reduces the error and increases the maximum measurable distance of the rangefinder

Night vision device

Improves visibility by enhancing natural light or active illumination.

Thermal imager

Allows to see thermal radiation in the infrared range day and night

Main armament

120 mm Rh120 L/44 cannon

Two-plane stabilizer

Reduces the swing of the gun in two planes while moving

Ammunition42 rounds

First-order15 rounds

Reloadbasic crew → aces

7.8 → 6.0 s

Vertical guidance-9° / 20°

The famous Rheinmetall L/44 120 mm cannon is mounted as the primary armament on the Leopard 2A4, offering a balance of firepower, accuracy and sustained rate of fire. The 2A4 has three rounds available to it: DM12 HEATFS, DM13 APFSDS and DM23 APFSDS. Of these, only DM12 is available when the vehicle is stock, with DM13 a tier 1 and DM23 a tier 4 modification. The L/44 is reasonably accurate at long range with any ammunition, however minor round deviation may be evident at extreme ranges (over 2,000 m).

It's advisable to primarily rely on the best available APFSDS round for engaging other MBTs, however, retaining a couple of DM12 rounds can prove valuable against lighter vehicles such as the ADATS.

120 mm Rh120 L/44					Turret rotation speed (°/s)					Reloading rate (seconds)
Mode	Capacity	Vertical	Horizontal	Stabilizer	Stock	Upgraded	Full	Expert	Aced	Stock	Full	Expert	Aced
Arcade	42	-9°/+20°	±180°	Two-plane	38.1	52.7	64.0	70.8	75.3	7.80	6.90	6.36	6.00
Realistic					23.8	28.0	34.0	37.6	40.0

Ammunition

Penetration statistics
Ammunition	Type of warhead	Penetration @ 0° Angle of Attack (mm)
		10 m	100 m	500 m	1,000 m	1,500 m	2,000 m
DM12	HEATFS	480	480	480	480	480	480
DM13	APFSDS	393	390	384	376	367	359
DM23	APFSDS	410	408	401	393	384	376

Shell details
Ammunition	Type of warhead	Velocity (m/s)	Projectile mass (kg)	Fuse delay (m)	Fuse sensitivity (mm)	Explosive mass (TNT equivalent) (kg)	Ricochet
							0%	50%	100%
DM12	HEATFS	1,140	13.5	0.05	0.1	2.15	65°	72°	77°
DM13	APFSDS	1,650	4.44	-	-	-	78°	80°	81°
DM23	APFSDS	1,640	4.3	-	-	-	78°	80°	81°

Ammo racks

Ammo racks of the Leopard 2A4

Full ammo	1st rack empty	2nd rack empty	Visual discrepancy
42	16 (+26)	1 (+41)	No

Notes:

• Shells are modeled individually and disappear after having been shot or loaded.
• Rack 2 is a first stage ammo rack located within a blow-out containment
• It totals 15 shells and gets filled first when loading up the tank and emptied first when firing.
• If you pack 16 (+26) shells, it will keep the hull empty of ammo.
• Full reload speed will be realized as long as shells are available in the ready rack 2. If the ready rack is empty, a penalty to reload speed will occur.
• Simply not firing when the gun is loaded will move ammo from rack 1 into rack 2. Firing will interrupt the restocking of the ready rack.

Machine guns

7.62 mm MG3A1 machine gun (coaxial)

Ammunition4 600 rounds

Belt capacity200 rounds

Reloadbasic crew → aces

10.4 → 8.0 s

Fire rate1 200 shots/min

7.62 mm MG3A1 machine gun

Ammunition2 000 rounds

Belt capacity200 rounds

Reloadbasic crew → aces

10.4 → 8.0 s

Fire rate1 200 shots/min

The 2A4 is equipped with one pintle-mounted machine gun and one coaxial machine gun. These can be used as an anti-air deterrent or for clearing out light obstacles and crew from open vehicles.

7.62 mm MG3A1
Mount	Capacity (Belt)	Fire rate	Vertical	Horizontal
Coaxial	4,600 (200)	1,200	N/A	N/A
Pintle	2,000 (200)	1,200	-10°/+75°	±180°

Usage in battles

The Leopard 2A4 may feel somewhat sluggish when stock, and the DM12 HEATFS round may appear to be relatively ineffective. Prior to researching improved rounds and engine modifications, it may be wise to play conservatively.

Once the vehicle's modifications are all researched, however, the 2A4 becomes significantly more mobile and has a competitive, albeit not impressive round in the DM23 APFSDS. The 2A4 can be used comfortably in both urban and rural environments, providing the vehicle's weaknesses are kept in mind. While it is capable in most forms of engagement, it does lack the precision of the British Challenger MBTs or the extreme round velocities of the Soviet T-64/T-80 series. The 2A4 also has a particularly large and blocky profile, making for a particularly visible target in many situations.

Considering the above, a Leopard 2A4 player should utilise its great mobility and competitive gun to get into early positions to pick off unsuspecting targets, rather than attempting to engage opposing forces head-on.

Pros and cons

Pros:

• Powerful engine, high top speed and acceleration
• Good neutral steering system
• Good gunner sight magnification for long-range engagements
• Reasonably high-velocity kinetic rounds
• Competent DM23 APFSDS
• Turret armour is mostly effective for hull-down engagements
• Primary ammunition is contained within a storage unit with blow-out panels
• Generation 1 thermals in the gunner sight

Cons:

• Hull armour is mediocre, particularly against kinetic rounds
• The stock DM12 HEATFS round can prove relatively ineffectual when compared to DM13/DM23, particularly against targets with ERA
• The gunner's optics are a weak spot, enemies who know how to aim can cripple your gun and kill your crew
• The gun mantlet is relatively weak while being quite prominent, penetration can disable the gun or knock turret crew out
• The turret cheeks can be penetrated by most APFSDS rounds when hit at the right angle
• Secondary ammunition storage is extremely vulnerable, although this is avoidable by carrying no more than 16 rounds
• Both machine guns are relatively light calibre, suffer from mediocre gun elevation and will not prove to be much more an annoyance to aircraft, particularly helicopters
• Blowout panels are unreliable and have a low capacity

History

Based on the testing results gathered from the various different Leopard 2K prototypes, a new Leopard 2 prototype was constructed that would be more representative of the final version of the vehicle. Designated as Leopard 2AV, the new prototype featured a redesigned hull and turret over the Leopard 2K. Furthermore, the prototype was tested with two different cannons; the British rifled 105 mm L7 and the German 120 mm Rheinmetall L44 smoothbore cannon.

In 1976, the Leopard 2AV was sent overseas to the United States to be comparatively tested against the new American state-of-the-art XM1 Abrams. During testing, the Leopard 2AV proved itself as a good counterpart to the Abrams, outperforming its competitor in terms of fire accuracy, whilst demonstrating somewhat inferior protection and gun handling. Upon arriving back to its homeland with positive testing results, the decision was made to begin mass production of the Leopard 2 in 1977.

The production version Leopard 2, however, differed from the AV prototype in receiving an increased level of protection before mass production began. Mass production of the Leopard 2 started in 1979 with the Leopard 2A0 forming the first batch that would enter service with the German Bundeswehr in late 1970s.

Throughout the production period of the early Leopard 2 versions, modernization and upgrades were being applied on the assembly line in order to keep the newest Leopards up to the latest standards. These modernization efforts mostly involved the upgrading of internal modules such as the aiming and communications systems. As a result of this, all early Leopard 2s (A0-A4) were visually neigh identical to each other. The Leopard 2A4 was the final early Leopard 2 variant before the more advanced and heavily upgraded subsequent Leopard 2 versions made their appearance as part of a new wave of modernization efforts.

A total of 695 Leopard 2A4s were built out of the total of 2.125 early Leopard 2s that were manufactured between 1979 - 1991. The Leopard 2 and its variants served primarily with the German Bundeswehr, but a number of export vehicles were sold to nations world-wide, ranging from Canada and Chile, over Denmark and Austria to Greece and Turkey to name a few.

-From Devblog

Media

Skins

• Skins and camouflages for the Leopard 2A4 from live.warthunder.com.

Photos

• 

  A Leopard 2A4 on display at the Bundeswehr Military History Museum.

• 

  Leopard 2A4 in Austrian service.

Videos

The Shooting Range #101 - Metal Beasts section at 00:31 discusses the Leopard 2A4.

See also

• Leopard 2 (Family)

External links

• MTU Defense Brochure
• [Devblog] Leopard 2A4: Setting The Standard