Marder III

Marder III

Sd.Kfz.251/9

StuG III A

Marder III

Sd.Kfz.251/9

StuG III A

Germany

I Rank

Battle rating:

AB	RB	SB
2.3	2.3	2.3

Class:

Tank destroyer

Research:5 900

Purchase:6 300

Show in game

This page is about the German tank destroyer Marder III. For other uses, see LT-38 (Family).

Description

The Marder III is a rank Marder III German tank destroyer with a battle rating of 2.3 (AB/RB/SB). It was introduced in Update 1.43.

The armour of the Marder is its biggest fault. Because it is open-topped, strafing runs from fighter planes can disable the crew very easily, even leading to ammo detonation! Enemy tanks only have this privilege because of poor positioning of the Marder, or because of a highly exploited breakthrough of allied defences. The front turret armour is also very thin and is vulnerable to basically any weapon save most 7.62 MGs. The hull armour at the front is rather thick at 50mm and is decently sloped for a tank destroyer. It still should not be relied on heavily, but if angled correctly it can be used to deflect British 2 pdr. guns, German, US and Russian 37mm and sometimes 50mm guns, as well as most ammunition used by the KV-1 series of tanks.

The Marder also has surprisingly poor manoeuvrability for a small tank destroyer. Being based on the Pz38(t) chassis, forward turning abilities slow the tank down significantly and neutral turning leaves a lot to be desired. The fact that the Marder has a forward facing gun with no turret means that it is required for the whole vehicle to turn to align the gun onto target if out of its arc of fire. Therefore, it is highly recommended to play with a squadmate or more mobile player, as the mobility of the Marder can significantly hamper urban combat abilities. Use the high speed of the Marder to reach a comfortable shooting position and stay there- the poor traverse and turning speed is fatal against nearly all turreted vehicles, along with the very poor armour.

However, the Marder makes up for most of these drawbacks with its high velocity, high damage 76mm cannon. It can OHK every single tank within the 1.7-3.7 BR range. Whether it be a Sherman, T-34, or Churchill, no UFP (upper front plate) is safe. Ballistics are very similar to all other 75mm long guns in the German line (IV F2, Marder III H, etc.), and thus experienced German tankers should not have issues assimilating to the Marder's cannon.

General info

Survivability and armour

Armour type:

• Rolled homogeneous armour

Armour	Front (Slope angle)	Sides (Slope angle)	Rear	Roof
Hull	50 mm (19°) Front plate 12 mm (74°) Front glacis 50 mm (13°) Lower glacis	16 mm Upper 15 mm Lower	15 mm	12 mm
Turret	11 + 8 mm (31°)	11 mm (8-9°)	N/A	N/A

Notes:

• Belly armour (under the tank) is 15 mm thick.
• Suspension wheels and tracks are 15 mm thick.
• Aside from the front gun shield, there is no armoured encasement for the gunner and loader crew members.
• The vehicle is so lightly armoured that it is extremely vulnerable to artillery strikes, plane strafings, ramming attacks and light machine gun fire.

Mobility

Game Mode	Max Speed (km/h)		Weight (tons)	Engine power (horsepower)		Power-to-weight ratio (hp/ton)
	Forward	Reverse		Stock	Upgraded	Stock	Upgraded
Arcade	47	7	11.3	227	305	20.09	26.99
Realistic	43	7		142	160	12.57	14.16

Armaments

Main armament

Gun and MG horizontal displacement of the Marder III

76 mm PaK 36(r)
Capacity			Vertical guidance	Horizontal guidance	Stabilizer
30			-6°/+18°	±10°	N/A
Turret rotation speed (°/s)
Mode	Stock	Upgraded	Prior + Full crew	Prior + Expert qualif.	Prior + Ace qualif.
Arcade	10.57	14.63	17.76	19.63	20.89
Realistic	7.14	8.40	10.20	11.28	12.00
Reloading rate (seconds)
Stock	Prior + Full crew	Prior + Expert qualif.	Prior + Ace qualif.
9.23	8.16	7.52	7.10

Ammunition

Penetration statistics
Ammunition	Type of warhead	Penetration in mm @ 90°
		10m	100m	500m	1000m	1500m	2000m
PzGr 39 rot	APCBC	138	135	124	112	101	91
Hl.Gr 38C	HEAT	100	100	100	100	100	100
PzGr 40	APCR	189	188	165	139	117	99
Sprgr. 39	HE	9	9	9	9	9	9

Shell details
Ammunition	Type of warhead	Velocity in m/s	Projectile Mass in kg	Fuse delay in m:	Fuse sensitivity in mm:	Explosive Mass in g (TNT equivalent):	Normalization At 30° from horizontal:	Ricochet:
								0%	50%	100%
PzGr 39 rot	APCBC	740	7.6	1.2	25	34	+4°	48°	63°	71°
Hl.Gr 38C	HEAT	450	5.1	0.0	0.1	875.5	+0°	62°	69°	73°
PzGr 40	APCR	990	4.1	N/A	N/A	N/A	+1.5°	66°	70°	72°
Sprgr. 39	HE	550	6.3	0.2	0.5	585	+0°	79°	80°	81°

Ammo racks

Ammo racks of the Marder III

Full ammo	1st rack empty	2nd rack empty	3rd rack empty	4th rack empty	5th rack empty	6th rack empty	7th rack empty	8th rack empty	Visual discrepancy
30	28 (+2)	25 (+5)	22 (+8)	17 (+13)	12 (+18)	9 (+21)	6 (+24)	1 (+29)	No

Notes:

• Turret "cheeks" empty (racks 1 & 2 empty): 25 (+5).
• Right flank empty of shells (racks 1 to 5 empty): 12 (+18).

Machine guns

7.92 mm MG37(t)
Mount	Capacity (Belt)	Fire rate	Vertical	Horizontal
Hull	1,200 (200)	769 shots/minute	-11°/+20°	±10°

Usage in battles

Offensive role

The Marder III should be played as a long range sniper, taking advantage of the APCBC shell's high penetration values, high gun accuracy and good mobility. Find a shooting spot and engage targets from at least 1,000 m away to prevent enemy progress towards the objectives. You will also suppress enemy fire to prevent your team from being pinned down by enemy snipers attempting the same in return. Because of your weak armour and open turret, always stay away from the frontline to avoid being flanked or swarmed and thus maximise your chances of survival. When engaging enemy tanks, prioritise firing hull-down from behind cover. With such firepower, any enemy wandering in your sight alone is practically dead. A flanking enemy, artillery strikes or CAS will be the greatest threats to the Marder III.

Defensive role

In case of an enemy breakthrough, your role is to contain the enemy advance by pinning them down. The enemy will be moving the front line, so engagements will take place at a closer range than you're comfortable with. You should identify and target in priority choke points, narrow passages and corridors of the map that the enemy will be forced to take. Your limited gun traverse still allows you to monitor an area spanning 350 m at 1,000 m distance without having to reposition your hull.

Other roles

If you try to use the Marder III in a different role on the battlefield, you will be confronting with the following:

• If you try to play the Marder III as a front-line tank, you will be quickly disabled by any type of fire coming from enemy tanks. Your armour is extremely thin and your open turret crew is very exposed to MG fire, artillery strike, HE shells blast or ramming attacks. Your turning speed is also too poor to manoeuvre quickly enough in close combat.

• If you attempt to play support tank, your poor reverse speed will make it difficult for you to overextend. Your high profile will make it difficult to stay hidden behind obstacles without taking fire. The enemy will flush you out with artillery strike (which can be accurate enough from middle ranges to disable you). Even with an escape route planned and cover to hide behind, your chances of survival are meagre. You will also be at risk of being flanked by light tanks or armoured cars, especially if they swarm you. Anyone who manages to get behind you has a very high chance to destroy you, even with just machine gun fire.

Notable enemies

• Any tank will disable you with little effort in a close range encounter because of your weak armour.
• For long range engagements, T-34s & M4s are the enemies most likely to bounce your shell if they are properly angling from a distance.

Defeating a Marder III

• If you are alone, flanking a Marder III undetected remains your best chance to destroy it. But it is difficult because the Marder positions itself very far from the frontline.
• Force the Marder III out of position with indirect fire (artillery strikes) if you're at relative close range.
• The most suitable shells to deal with a Marder are HE, HEAT or Shrapnel shells.
• In case of a frontal attack (choke point/corridor), try blinding the Marder III with smoke and then swarm it with several tanks to saturate its defensive capacities. A barrage of MG fire is very likely to make a Marder III retreat and relocate.

Modules

Tier	Mobility		Protection	Firepower
I	Tracks		Parts	Horizontal Drive
II	Suspension	Brake System	FPE	HLGr 38C	Adjustment of Fire
III	Filters		Crew Replenishment	PzGr 40	Elevation Mechanism	Smoke grenade
IV	Transmission	Engine

Which modules to unlock first:

• Parts and FPE - Mandatory first 2 upgrades, to guarantee your survival.
• Modules related to gun accuracy and targeting quality: Horizontal Drive, Adjustment of Fire & Elevation Mechanism.
• Modules related to mobility: Tracks, Suspension, Brake System, Filters, Engine, Transmission.
• Smoke grenade and Crew Replenishment, to increase your survivability.
• Research the shells last, the stock shell offering the best post-penetration damage.

Pros and cons

Pros:

• Good gun penetration
• Powerful at all ranges
• Relatively high forward speed
• Relatively good HE filler in APCBC rounds
• Average hull armour of 50 mm
• Capable of penetrating all tanks frontally at its BR range (1.7-3.7)
• High capacity spotting machine gun in the hull

Cons:

• Tall profile, hindering concealment ability
• Slow turning movement
• Very prone to falling over due to height, especially for newer players with low amounts of invested crew points towards driver
• Very thin gun shield for the gun crew
• Open top vehicle, gunner and loader can be easily machine-gunned
• Vehicle can be hull broken
• Will struggle against heavily sloped armour due to penetration drop-off with increasing angle-of-attack

History

Development

After the start of Operation Barbarossa, the Wehrmacht found a very dire problem of the lack of a mobile anti-tank system and adequate anti-tank weapons, especially after the appearance of the Soviet T-34 and KV-1 tanks. The only mass-issued anti-tank was the fairly weak 37 mm Pak 36 and the only mobile anti-tank system widely used was the Panzerjäger I with the Czech 47 mm anti-tank gun. Modifications to current vehicles in service was done to put more self-propelled anti-tank weapons into service, which created the Marder I from the French Lorraine, the Marder II from the Panzer IIs, and the Marder III from the Czech Panzer 38(t).

Specifications

The Marder III, with the rest of the Marder series, gave Germany forces a self-propelled gun mounting a better gun than what was available on German tanks, such as the 75 mm Pak 40 or captured Soviet 76.2 mm guns chambered for the Pak 40 ammo. All of the Marders share a lack of armour for the crew, the top and rear of the vehicle is left exposed to mortar, shrapnel, or infantry weapons. This weakness is mitigated with the fact that the Marders are supposed to be anti-tank motor carriages that are to ambush incoming enemy tanks.

The Marder III use the Panzer 38(t) as it was a design going obsolete, and lots of Soviet 76.2 mm guns were captured, so they mounted these guns onto the Panzer 38(t) first. The finished self-propelled mount had a higher silhouette than the Panzer 38(t), which left it more vulnerable, but had a rechambered 76.2 mm Pak 36(r) gun with the Pak 40 ammo and could hold 30 rounds in the vehicle. A machine gun on the hull was retained for anti-infantry purposes.

The Marder III with a 75 mm Pak 40 gun mounted instead of the rechambered 76.2 guns was called the Marder III Ausf. H. Another variant created, the Ausf. M, featured a lower silhouette and a better-sloped armour and fighting compartment, despite only holding 27 rounds for the mounted Pak 40. A total of 3,472 Marder IIIs and its version was created or converted from Panzer 38(t) during its production life.

Combat usage

The Marder III fought on all front of the war, being produced from 1942 to 1945, with 2,080 Marder III with the 76.2 mm gun converted and produced. Using the tested design of the Panzer 38(t), the Marder III experienced a reliable mechanical history and has a gun that could take out most allied tanks in the war. The vulnerability to the crew due to lack of armour was its most pressing issue, with only a front shield plate at most 15 mm thick and side plates that can't enclose the crew. This makes it as very poor assault vehicles or tank substitutes as the open top could allow infantry to easily kill the crew from hidden areas, despite that, it is sometimes repurposed to this role to the chagrin of the crew.

As its production was underway, Germany already had a few self-propelled assault weapons being produced such as the StuG III that could have the same anti-tank capabilities, yet was fully-armoured, enclosing the crew in adequate armour. This obvious advantage over the open Marder series encouraged the development of a new kind of tank destroyer from the Panzer 38(t) with better armour, which will eventually create the Jagdpanzer 38(t). Despite that, the Marders continued to serve to the end of the war.

In-game description

An antitank vehicle designed on the basis of the Pz.38(t) tank by the BMM company (formerly ChKD) by installing a 76.2mm F-22 division cannon on the chassis of a captured Soviet tank that had been modified by German engineers. The impetus for building this platform was the fact that in 1941 it became clear on the Eastern Front that the Wehrmacht did not have the means to fight Soviet heavy tanks. At the time, the captured 76.2mm F-22 division cannon was able to fight these tanks, so they decided to install it on the reliable frame of the Pz.38(t). BMM produced 344 of these antitank vehicles.

Media

Skins and camouflages for the Marder III from live.warthunder.com. Watch out for the "Marder III H" entries as they will not fit on this first version. You need the ones with the small, not rounded turret.

Read also

Official War Thunder forum article: [Vehicle Profile] Marder III

Sources

Paste links to sources and external resources, such as:

• topic on the official game forum;
• other literature.