Difference between revisions of "M4 Sherman (Family)"

From War Thunder Wiki
Jump to: navigation, search
Line 49: Line 49:
 
<!-- == History ==
 
<!-- == History ==
 
''Describe the history of the creation and combat usage of the vehicle family in more detail than in the introduction. Be sure to reference text and sources by using <code><nowiki><ref></ref></nowiki></code>, as well as adding them at the end of the article with <code><nowiki><references /></nowiki></code>. This section may also include the family's dev blog entries (if applicable).'' -->
 
''Describe the history of the creation and combat usage of the vehicle family in more detail than in the introduction. Be sure to reference text and sources by using <code><nowiki><ref></ref></nowiki></code>, as well as adding them at the end of the article with <code><nowiki><references /></nowiki></code>. This section may also include the family's dev blog entries (if applicable).'' -->
 +
== Variants and Upgrades ==
  
=== M4A3E2 Sherman "Jumbo" ===
+
===M4A3E2 Sherman "Jumbo" ===
  
 
==== Design ====
 
==== Design ====

Revision as of 17:46, 30 June 2020

Description

The M4 Sherman, designated Medium Tank, M4, named after the American Civil-War General William T. Sherman.

The M4 was the most widely-used American tank ever developed, originally meant for World War II, but seeing service far after 1957, when the US retired them, with its latest retirement nation being Paraguay in April 2018.

Vehicles

Rank II

Rank III

Rank IV

Other

Variants and Upgrades

M4A3E2 Sherman "Jumbo"

Design

Hull

The M4A3E2 had 1.5 in (38 mm) armor plates added to the front and upper sides of the hull. The additional armor was welded onto the original armor, which brought the total thickness of the frontal armor to 4 in (101 mm) and the upper side thickness to 3 in (76 mm). The rear and top armor remained the same, and the lower hull sides were also unchanged. The frontal plate had a cutout in the hull to allow for fitting the plate over the machine gun ball mount. Additionally, the final drive assembly cover was replaced by a more heavily armored version. The thickness was from 4 in (101 mm) to 5.5 in (129 mm).

Turret

The M4A3E2 received a new turret. The new turret was based on the T23 turret (used on 76 mm gun armed Shermans), but it had the pistol port removed. The armor was also increased to 6 in (152 mm) all round, but the area under the rear turret basket was only 2.5 in (63 mm). Despite using the M62 gun mount that was normally used for 76 mm guns, a 75 mm gun was mounted as standard. The standard 2 in (50 mm) gun shield had 5 in (127 mm) armor added to it, increasing both the size and thickness of the mantlet. The standard ammunition load was 104 75 mm rounds, 600 .50 cal (12.7 mm) rounds, 6250 .30 cal (7.62 mm) rounds, 900 .45 cal rounds for the crew's defensive pistols, 18 hand grenades, and 18 2 inch smoke grenades.

Note: Many M4A3E2 Shermans were up-gunned to the 76 mm caliber during the war.

Mobility

Because of the immense weight of the additional armor, extended end connectors were fitted to the tracks, reducing the ground pressure. The engine was the same Ford GAA V8 as was standard on the M4A3. The maximum speed was reduced to 22 mph (35 kph), but the acceleration was still manageable. It could climb a 60% slope, cross a 7’6” (2286 mm) trench, climb a 24” (609 mm) vertical wall and ford 36” (914 mm) of water.

Media

Videos